Skip to main content

Calculator

DG Fuel Consumption & Efficiency Calculator

Enter your DG set's rating, load, hours and the diesel it actually used. Get litres per hour, kWh per litre, load % and fuel cost per unit — for a 125, 250, 500 kVA or any size set.

Quick Answer

DG efficiency on site = kWh generated ÷ litres of diesel used. Fuel per hour = litres ÷ hours run. Load % = average kW ÷ (kVA × 0.8).

  • Fuel per hour depends on load. Fuel per unit (L/kWh) is what tells you whether the set is running well.
  • Use real numbers: litres from your fuel register, kWh from a meter on the DG output.
  • Track kWh per litre over weeks. A drop at the same load is the early warning.

The figures in the calculator are example inputs only — replace them with your own.

Inputs

Result

Units per litre
3.20kWh/L
Fuel per unit
0.313L/kWh
Fuel cost per unit
₹28.75/kWh
Average load
60% of rating
Units generated
480kWh
Fuel rate
18.8L/h
Rated output
100kW
Fuel cost only. Lube, service and the set's capital cost are extra. Total diesel cost: ₹13800

How the calculation works

Rated kW = kVA × rated PF
Load % = Average load kW ÷ Rated kW × 100
kWh generated = Average load kW × Hours run
Litres per hour = Litres used ÷ Hours run
kWh per litre = kWh generated ÷ Litres used
Fuel cost per kWh = (Litres used × ₹/L) ÷ kWh generated

The weak link in most DG calculations is the load figure. An “estimated 60% load” can easily be 40% or 80% in reality, and every result above moves with it. Measure the average kW on the DG output with an energy meter for the same period as your fuel reading, and the numbers become reliable.

For an hour-by-hour figure, read the fuel consumption table in your engine maker's datasheet — it gives litres per hour at set load points — and use this calculator to compare it with what your set actually does.

Why kWh per litre is the number to watch

  • It separates load from performance. Litres per hour rises and falls with load; kWh per litre at a similar load should stay steady.
  • It shows light running. The same set usually gives fewer units per litre at light load than near its rating.
  • It exposes fuel losses. If litres go up but kWh does not, the diesel is going somewhere other than the engine — a leak, a wrong register entry or theft.
  • It gives a true cost per unit. Compare it with your grid tariff in the diesel genset vs grid calculator.

Measure it automatically instead of by hand

A Titan energy meter on the DG supply takes a 12 V signal when the DG is on and records DG energy (kWh, kvarh, kVAh) in its own registers, separate from grid energy, together with DG run hours, load and power factor. That gives you the kWh and hours side of this calculation continuously, with no manual readings.

For the fuel side, Titan can read the genset controller over its RS485 port, including the level from the controller's fuel sensor, along with the engine readings and alarms the controller reports. Put together, that is units per litre, load and engine condition on one dashboard. See generator monitoring for how the system fits together.

Many DG rooms have no WiFi. For those sites, Titan 4G sends the same data over a mobile network using MQTT.

Frequently asked questions

DG fuel consumption, efficiency and load.

Record the litres used over a run (from the fuel register or tank dip before and after) and the hours run. Litres ÷ hours gives litres per hour. To judge efficiency, also record the units generated (kWh) over the same run from an energy meter on the DG output, then divide kWh by litres. That kWh per litre figure, tracked over weeks, is the practical efficiency number for a diesel generator.
It depends mainly on the load, not just the kVA rating. A set running at a quarter of its rating burns far less per hour than at full load, but usually more per unit generated. Use the fuel consumption table in your engine maker's datasheet, which normally lists litres per hour at 25%, 50%, 75% and 100% load, as the starting point, then check it against your own fuel register with this calculator. We do not quote a single generic figure because it would be wrong for most sites.
Strict thermal efficiency needs the fuel's energy content and lab-grade measurement. On site, the useful measure is units per litre: kWh generated ÷ litres consumed. Higher is better. Compare the same set month to month and at different loads. A falling kWh per litre at the same load points to a problem worth investigating — injectors, air filters, fuel quality or fuel losses.
Wet stacking is unburnt fuel and soot building up in the exhaust when a diesel engine runs for long periods well below its rated load, because the engine does not get hot enough to burn the fuel completely. It also raises fuel per unit. Engine makers state a minimum recommended load in the manual — enter it in the calculator to flag light running against your own engine's figure.
Multiply the kVA rating by the rated power factor, which is 0.8 on most DG nameplates. A 125 kVA set is therefore about 100 kW; a 500 kVA set about 400 kW. Load % in this calculator is measured against that kW figure.
Yes. A Titan meter on the DG supply takes a 12 V signal when the DG is on and records DG energy in its own registers, separate from grid energy, along with DG run hours, load and power factor. Titan can also read the genset controller over its RS485 port, including the controller's fuel level sensor, so units per litre can be tracked without a manual register.

Track your DG's units per litre automatically

Tell us the DG rating and how many sets. An engineer replies within 24 hours with the meter, CTs and a price.